10 Quick Tips On Audi G28

How to Replace an audi smart key replacement G28 Engine Speed Sensor

In this video, Charles the Humble Mechanic demonstrates how to replace the G28 engine speed sensor. This sensor is located near the edges of the transmission, above the flywheel ring gear. It transmits a signal to the ECU via the grey wire (T55/49), then to the tachometer in the instrument cluster.

1. Engine Speed Sensor

The sensor is located at the edge of the transmission above the flywheel ring gear G28 Engine Speed Sensor sends signals to ECU pin T55/49 via a grey wire. The ECU then utilizes this information to regulate the flow of fuel, timig and boost. It also sends an alert to the G5 Tachometer within the instrument cluster.

The sensor is used to link the G40 Camshaft position Sensor. The ecu needs to know when the crankshaft is TDC and where the camshaft is located so that it can activate spark and injectors according to the situation.

If this sensor fails, the ECU will show an error code P00160 which indicates that the Crank Shaft and Intake Camshaft aren't in sync and could indicate the chain stretching or a jump link on the upper chain of timing. The code will not appear without the additional information provided by other sensors (G4 or G40).

Testing can be a bit difficult as there are two different connector pins and replacement audi car key (https://fewpal.com) they have different functions however the best method to test it is to measure resistance between the sensor and the ECU. When the sensor is operational, it should be reading around 1000 ohms. If you are having problems with this component, look for signs of oil or coolant in the connector bay.

2. Injectors

Yesterday, when accelerating from highway paytoll at maximum speed I noticed a massive drop in power. It was as if the engine had run out of gas. Or, my injectors weren't firing. Today, i pulled out the spark plugs, three were soaked with gazoline and the fourth was dry. I put tissue over each hole in the injector and when i start the engine with no sparks, the 3 that have gazoline pop right out. The fourth one remains closed. I checked the ground connection of ECU pins 14,30 and 48/55. I found zero ohm. I'm assuming the issue is in another place.

I also tried to reset the PID without success. The car is able to start when the G28 is not plugged in and is running fine when it is connected but it still is experiencing intermittent misfires at higher RPM. The coolant sensor (G62) even when it is unplugged, shows an ice temperature of -49c. I also noticed that the oil pressure gauge in the cockpit is showing 2 bar while the actual pressure is 0.0 when i rev the engine.

I'm not sure what to do, as i believe that i've ruled out everything else. However, i'm afraid that I may have missed something. If anyone has any ideas please share them! TIA!

3. Fuel Pump

The fuel pump of the g28 receives signals from the RPM sensor. The GM-style transmitter is identical to the G4 and they both work in the 80, 100, 200, UrS and RS2 cars so you can easily find one at a junkyard or in a local parts store. It is easy to test them - just switch your DMM into resistance mode and measure the distance between pins 1 and 2 (with the bump at the connector end facing up). They must be infinite Ohms.

4. ECU

Our 20vt turbo (3B AAN, ABY, and ADU) engines are equipped with an ECU that must know the speed and position of the crankshaft in order to make decisions about timing of the fuel injectors, etc. It uses a Crank Position Sensor G4 and an Engine Speed Sensor G28 to accomplish this. If either of these goes bad you will get codes on the diagnostic scanner which can cause the engine to shut down.

Some of the signs of a failing G28 sensor are an inaccurate rev counter in the gearbox and gears that shift faster than normal, and/or a misfire when in gear. If you experience any of these issues, it is most likely that your sensor is deteriorating and requires replacement. They're cheap and easy to find, especially if they're an Bosch sensor like ours. You can also choose the GM version of this unit is also a good option.

5. Tachometer

A damaged engine sensor could cause a myriad of issues in your car. It is a crucial part of the audi car key replacement cost tt replacement audi spare key (sneak a peek at this site)'s transmission as it sends information to the ECU about how fast or slow the vehicle's crankshaft is rotating. This sensor could cause the transmission to malfunction and other car components to be affected.

The G5 engine sensor is located at the edge of the transmission, just above the flywheel ring. It sends a signal via a gray wire to the ECU pin T55/49. The ECU is then able to process the signal to control fuel, timig, and boost, and also transmitting it to the G5 tachometer inside the instrument cluster. You can determine if the sensor is in failure by examining the continuity of the sensor to the tachometer. Also, you can check continuity between pin T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79trace [79]), and between pin T6a/1 as well as pin T26a/12. You should detect a resistance of approximately 1000 ohms between these points. This is a typical component across the audi spare key 80 100 200, UrS and RS2 range from 1985 MC until the 1997 UrS AAN and 1995 RS2 ADU, so the best parts could be found in wrecking yards.