The 10 Scariest Things About Car Key Button Repair

Car Key Button Repair

A damaged car key button can be a hassle. You may need to contact the 24 hour Locksmith Service or purchase a replacement remote.

But, you may be saving money by fixing an old key fob instead of replacing it. This is especially true when the switch is worn out or has faulty contacts are at the root of the problem.

Battery

If the buttons on the key fob aren't responding to pressing, this could be a clear sign that the battery is dying or nearing the end of its lifespan. It's easy to replace the battery yourself, rather than paying for an auto locksmith or dealership.

First look for the battery compartment. The battery compartment is usually located on the back of the key fob and can be hidden behind a cover that can slide out or an open button that opens the access point. When the compartment is open you can look for the tiny button-cell battery. It is usually shaped like a coin and marked with an minus and plus sign. Remove the old battery and insert a new one in its place, ensuring that the plus and minus marks are properly aligned.

Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the components in the correct position. To test that the buttons work properly Press any of them.

If your remote key fob repair near me keyfob does not work after replacing the battery, it could be other issues that require a different kind of repair. The fob's dropping into a puddle can cause it to cease functioning. It could also be a problem with the internal electrical system or need to be deprogrammed. Check out these other common car troubleshooting tips to see whether your key fob may be having a problem of its own.

Switches

There are various types of switches found in the car key fob dependent on the year and model. The older style key is equipped with a chip that is visible inside the case. The modern keys function by transmitting signals to your car. Regardless of the type, the buttons on the key can become worn out or damaged when used regularly. They become hard to press or not responsive. If you force the button it can cause further damage. It may also prevent the key from working in the future.

If your key doesn't seem to be working, you should first try changing the battery. If this doesn't work, then you might need to clean your key's fob or re-adjust the switches. These tiny electronic switches are more prone than larger components of the key to break due to the fact that they are constantly jostled.

The switches are made of rubber, and are coated with an electrically conducting film that is prone to wear out over time. Luckily, they're also a very small part and inexpensive to replace. They're soldered to the circuit board, so you need to carefully take them off without causing any damage to anything else. Then you can put in the new ones and reassemble your key fob.

A good way to keep your car key fob from becoming damaged is to not use it for more than a few hours at a time, and also to not leave it in visible locations where it can be seen. Also, make sure you find a secure location to keep your key repair car in when you're not using it.

If the issue continues to persist after you've cleaned the key fob replaced the battery and tried to clean it, then you might need to contact a locksmith. A professional can test the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, swap cases, and more.

Outer Case

A key fob spends many hours bouncing around and if the buttons aren't free to move up and down within the case they can get stuck or break. If replacing the battery or cleaning with a cotton swab and some rubbing alcohol don't resolve the issue, taking off the case and examining it could be required. If the contact points where the buttons touch aren't fitting well or are worn out, adjusting them might be the only solution to fix the problem.

Rubber buttons be worn out over time. The rubber expands and nails cut into it and the buttons can become difficult to press. This can cause the key to fail and in this instance it's time to get the replacement of the case or buttons. This repair involves removing the remote key fob repair near me, then locating the buttons on the circuit board, then heating the solder, and then carefully remove them. New buttons are then attached to the circuit board. The case is then put back together with the horseshoe key blade piece attached. The new buttons must be snugly fitted into the case in order to prevent them from falling out.

Inner Case

Over time the buttons on your key repair service fob can be damaged or stuck because of the constant jostling and accidental pressing. If your key fob ceases to function while you are away from home, you can fix the issue fast by using metallic tape and punch holes. This allows you to unlock doors but not start the car. This quick fix could allow you to safely return to your vehicle and complete your journey.