10 Things Everyone Gets Wrong Concerning Replacing Upvc Window Handles

Replacing uPVC Window Handles

It is simple to change the handles on windows made of upvc. The important thing is to make sure that the new handle is a good fit for the spindle that was cut out of the window mechanism.

If you follow the steps below, any cockspur handle will fit most windows. The most important factor is the step in the height of the handle.

What to Look For

Over time, uPVC handles on many windows in the UK begin to show signs of wear and tear. When this occurs, the handle may become loose or difficult to operate, making it necessary to replace it. This is a fairly simple job that can be accomplished by anyone who is comfortable using basic hand tools.

The first step is to ensure that the handle is securely attached to the frame of the window and in its open position. The next step is to find the fixing pins or screws that hold the handle in position. These are typically located on the inside face of the handle and are removed with a screwdriver, or pliers.

Once the handle has become loose, gently pull it away from its hinges. Then, you'll need to find a new handle of the same dimensions and style. This can be done online or in the local DIY store and it should take five minutes using an screwdriver.

When replacing the handle on a uPVC handle, it is important to think about the step height. This is the distance from the base of the handle to where it sits on the window frame. This is a common measurement and you should check the step height before ordering the replacement handle.

Depending on the type of handle you have, there are different sizes available. Inline handles for uPVC windows typically have lug centres of 31mm as well as handles with cockspur with 43mm centres. Tilt and turn handles are typically found on uPVC windows, and they feature a specific design that allows windows to be slid up to allow for ventilation, and then turned to fully open the window.

The most frequent uPVC handle cracks are internal, instead of a break at the base. This makes them difficult to open and is why it is important to make sure that the replacement handle you purchase has the same length of spindle that your current one.

Remove the handle that was previously used

If the handles on your windows are damaged or incorrectly fitted, they can cause double-glazed windows to not open or close correctly. They may even get stuck. There are a myriad of reasons, such as general wear and tear or the corrosion of the metal handle. In these situations, it is important to find replacement handles made of upvc as soon as you can to avoid further damage and loss of functionality.

One of the first steps that you should do when replacing upvc window handles is to remove the old handle from the window. Begin by removing the screw with the handle when it is in a closed position. Once you have removed that screw, you can remove the handle. You can make the job easier by using an electric screwdriver.

Be aware that screws may be hidden under caps made of plastic. It is best to remove the covers with the help of a Stanley knife. After the old handle has been removed, you must examine the square cut out at the handle's base to ensure that the new window lock handles will work with it. This is important as you'll need to measure the length of the spindle of the old handle to ensure it matches the size of the window mechanism and the handle spindle cut out.

The different kinds of window handles made from upvc include: Espag handles, which feature a central screw that will turn left or right; Cranked handles that have two screws and are found on tilt and turn windows made of upvc as well as Spade handles, which have an arm that is flat and can be placed on either side of the window. Once you have a suitable replacement, it's simple to screw the handle into position and ensuring that the spindle is inserted into the euro lock handles mechanism. Once you have done this then tighten the handle to the window frame. The new upvc handles should now be secured.

Take a measurement of the Spindle

If you're replacing a Upvc window handle that has come off, it is likely because the spindle holding it in place is loose or damaged. In some instances, it can be fixed with screws or pins to tighten it. In other cases it will require replacement completely. There are several kinds of window handles made from upvc. They include espagnolette handles inline as well as cockspur handles. tilt and turn handles. Each handle type is installed and replaced in a different way.

Before you purchase a new handle, it is essential to know the dimensions of the one you have. This will help ensure that the new handle is of the correct size and will fit correctly within the window. All handles are measured according to industry standards, so it is easy to determine the right size.

To measure the size of your handle, first, take it out of the window by turning it to the open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Make use of a ruler or tape measure to determine the length the spindle is. Once you have determined the length of the spindle, you can purchase a new one with exactly the same size.

The step height of a upvc window handle is also important to take into consideration when you are buying a replacement. The step height is measured from the base to the point at which the handle is placed on the frame. It is typically around 21mm or 9mm in aluminium and uPVC. To ensure that the new handle will work the gap, drop something into the space to see how far it extends before it comes into contact with an obstruction.

Cockspur handles often have different backset heights based on the type of window they are placed in. Inline Espag handles have the standard height of 43mm from centre to centre (2 fixing points). Cockspur handles however have different backset heights according to the design of the window they are in. This is due to the fact that they have a spur which extends from the handle and is locked onto a cockspur wedge-striking plate.

Fit the New Handle

When you've chosen a new handle, carefully align it with the screw holes in the door and secure it using the screws provided. If you're also replacing the latch lever, it can be installed similarly to the patio door handle locks handle. Then, you can reattach the bifold door handles trim in order to conceal the mounting screws and close the project.

Tips: To remove the metal head from a wedge made of wood, place the handle on the floor so that its wide end is level with the ground. Then use a hammer and tap the thin end. Be careful not to scratch the handle or the handle spindle.