The 10 Most Scariest Things About Car Key Button Repair

Car Key Button Repair

A damaged car key button can be a source of frustration. You may need to contact an emergency locksmith service or purchase a replacement remote.

But, you may be able to save money by fixing an old key fob rather than replacing it. This is particularly true if the issue is caused by an old switch or a damaged contact.

Battery

If the buttons on your key fob don't respond to pressing the buttons, it could be an obvious indication that the battery is dead or nearing the end of its lifespan. Fortunately, replacing the battery is a simple task that can be completed by yourself rather than hiring a locksmith or dealer to take care of it.

Find the battery compartment first. The battery compartment is usually located on the back of the key fob and is often hidden behind a cover which slides out or an open button that opens the access point. When the compartment is opened, look for the small button-cell battery. It is usually shaped like an oblong coin and is identified with a plus and minus sign. Remove the old battery, and replace it with a brand new one. Make sure the plus and the minus symbols are properly aligned.

Close the compartment and snap together the two halves of your key fob. Before closing the door ensure that you align and snap the pieces in the correct position. Press any of the buttons to confirm that they function properly.

If your remote key fob ceases working even after you replace the battery, it could be suffering from other issues that require a different type of repair. The fob's dropping into a pool of water can cause it to stop working. Alternatively, it might be experiencing an internal electrical failure or it may require to be deprogrammed by an expert or locksmith. Also, take a look at these common car key fob repairs near me troubleshooting tips to see if your key repairs near me fob is suffering from a different issue.

Switches

Depending on the year and make, there are different kinds of switches that are found that are used in the keyfob of your car keys repair. The older style keys have an embedded chip that can be seen inside the case. The modern keys function by transmitting signals to your car key repair. No matter what type, the buttons on the key may become worn out or damaged with normal use. This causes them to become difficult to press, or even unresponsive. If you attempt to force the button to work the button, it could cause damage, and could even prevent the key from starting your vehicle in the future.

If your key doesn't appear to be working, first try changing the battery. If this doesn't work, you may have to clean your key's fob or adjust its switches. These tiny electronic switches are more likely than larger parts of the key to break since they are constantly jostled.

The switches are rubber-like, and are coated with an electrically conducting film that is prone to wear out over time. However, they're a small part that is easy to replace. The older ones are soldered to the circuit board, so you'll need to be careful to remove them without causing damage to other parts. You can then solder the new ones in and reassemble your fob.

Don't use your car key fob for more than an hour at a time, and do not leave it open. Also, make sure you locate a safe place to store your key when you aren't making use of it.

If the issue persists after you've cleaned your key fob replaced the battery and tried to clean it, then you may need to talk to a locksmith. A professional can test the frequency of your key to see whether it's still able communicate with your vehicle. They can also open and replace micro switches, alter cases and much more.

Outer Case

If the buttons don't move freely up and down in the case, they could be stuck or even break. If replacing the battery or cleaning it with a cotton swab and some alcohol rubbing doesn't solve the issue, taking off the case and inspecting could be required. If the contact points where the buttons touch aren't fitting well or are worn out, adjusting them may be the only way to fix the issue.

Some keys use rubber buttons which can wear away over time. The rubber expands and nails pierce it, and the buttons become difficult to press. In this situation the key could fail and it's time replace the case or button. This repair keys near me involves taking apart your remote, finding the buttons on the board, heating the solder and carefully remove them. The new buttons are then connected to the circuit board. The case can be rebuilt and the key blade of the horseshoe can be inserted. The new buttons must be a close fit into the case to prevent them falling out.

Inner Case

Over time the buttons on your key fob may be damaged or stuck as a result of the constant jolting and accidental pressing. If your key fob ceases to function when you are away from home, you can fix the problem quickly by using metallic tape and a punch hole. This will allow you to open doors but not start the car. This quick fix could allow you to safely make it back to your vehicle and continue your journey.