14 Companies Doing An Excellent Job At Door Lock Change
How to Do a Door Lock Change
Change your door lock is a simple and affordable way to improve the security of your home. The process is not for everyone. It requires some expertise and perseverance.
The cylinder is located within the knob's body. The cylinder is responsible for recognizing the key as it is inserted in the lock.
Remove the old lock
The first step to replace the door lock is to remove the old one. It's a simple process, but you must keep certain things in mind. Make sure that the new lock fits your door. This will ensure that it fits securely, and doesn't leave a gap in the latch or deadbolt.
After you've removed the latch plate look for two screws or bolts on the inside of the casing that connect the casing and halves of the lock together. Unscrew these with a screwdriver, then take the window lock replacements out of the door. If you have a mortise locking mechanism, there is a set screw that holds the handle to the spindle. Remove the doorknobs by unscrewing the screw using a screwdriver.
Remove the deadbolt and latch plug from your Door Lock Window Repairs jamb. Then, you can put in your new lock. If you are replacing window locks a mortise lock you should also measure the distance between the lock case and the edge of your door to ensure that your new lock will fit.
It is possible to replace your lock for a variety of reasons, such as when you suspect that someone else has the key or if you've got an incoming roommate. You can save money if you take the lock off yourself, instead of hiring for a professional. The process is easier than most people think, and it can be completed in just a few minutes.
Begin by getting rid of the handle and trim from your door. With a flat screwdriver, remove the trim. You should be able to twist off the majority of it. In some instances you might be able remove the handles completely. Next, search for a pinhole on the inside of the handle, and insert a straightened clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Look for a small tab on the interior of the lock and press it with a flat screwdriver. Once the spindle has been removed, you can remove the housing and cylinder.
Making a decision on a new locking system
You have many options when it comes to choosing the right lock. Take a look at the various types of locks and pick one that is in keeping with the design of your door. Consider the backset, which is the distance between the edge and the center of the hole in the lock. Also, think about the cross bore, a small hole in the middle of your door frame. Select a lock that is suitable for the door thickness and swing.
Most door locks have been evaluated by BHMA and the American National Standards Institute to provide you with an idea of how they stand up to use and how difficult they are to pick or disable. A double glazing window lock replacement of grade 3 could be the ideal choice for a tranquil apartment building in a rural area, whereas locks of grade 1 might be better suited to a busy street near an open-air storefront.
Most smart door locks require a digital key code to open. If you're concerned about security breaches or hacking seek out an expert locksmith or your local police department for advice.
Replacing the cylinder
If the cylinder of your door lock is broken or damaged you can repair it in just a few minutes with a simple do-it-yourself project. It is essential to choose the right cylinder and follow the instructions. First, remove the handle or knob if it is present. Then using a screwdriver remove the trim that is around the lock cylinder. Once the trim is removed, you can access the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently removed from the door.
Make sure you measure the length of the new cylinder before installing it. With a tape measure, determine the distance between the cylinder's center and the right and left sides. Then, you can purchase an additional cylinder using the same measurements. This will stop the cylinder from snapping, which could happen when the door is kicked out or when the key gets stuck inside.
If you have a suitable replacement cylinder, insert it into the door and turn the key. This will align the cylinder with the carriage which is located usually on the outside of the lock. Then, loosen the set screws which should be just a couple of turns inside the head. If there is a screw on the outside of the case that holds the door, you'll have to loosen it.
After removing the lock cylinder and replacing it with the new lock by sliding the new cylinder into the case and tightening the set screw. You should also reinstall the part that connects the cylinder with the lock indicator stem and this can be done by pulling out three tabs on the back of the cylinder using needle-nose pliers. Then, you can connect the remaining smaller bracket to the back of the cylinder. Then, you should reinstall the strike plate and latch plate as well as the retaining ring that is attached to the top lock cylinder.
Installing a new lock
Start by measuring the door's width if you are replacing a lock that is already in use. Most locksets for residential use are designed for a door thickness of 1 3/8 to 3/4 inch. If your door is more thick you will require a door kit that is thick and includes longer screws and a longer tail piece (for door knobs) or spindle extensions (for deadbolts).
Most locks come with a detailed instruction booklet to assist you in installing the new hardware. Before you begin, read the instructions to ensure you've followed the steps. The booklet will give you a clear idea of how much skill is required to complete the task. If you're replacing a lock for the first time, you might want to ask an experienced person for help.
It's a great idea to tape the openings in the old hardware prior to installing the new lock. This will prevent the screws from slipping out of the holes, and will protect any tile you might have installed in the area. It also protects against potential damage from rust dirt, and grime. SECURAM Touch comes with a piece of painter's tape that is intended to be used for this purpose, however you can also use gaffer's tape or masking tape if you have it available.
After you have removed the screws that hold the interior portion of the lock section to the exterior side then pull it out straight away. It is important to do this as quickly as possible to prevent the lock from closing itself in a way that could end up damaging the mechanism.
If your new lock has a latch bolt, fit the new bolt into its upper cross bore. Be sure to put it in the correct place that is usually indicated by an arrow on the faceplate. Next, fit the latch plate on top of the bolt and screw it in place.
Finally, screw in the deadbolt and strike plate into the door jamb. Test the deadbolt a few times, throwing it around to make sure it extends into the strike plate. If you're using an electronic smart lock, be sure to follow the instructions for programming it. This requires downloading an application and registering your e-mail address, confirming your identity and connecting to the wireless network to add your device.