The 10 Most Scariest Things About Repair Car Keys

How to Repair Car Keys

The car keys aren't big and might not seem to be important, but they are essential for the operation of your car. The cost of replacing a traditional or modern transponder car key could be as high as $200.

There are many ways to repair your car keys yourself for just a fraction of the cost. This article will cover the most frequently encountered car key problems and the DIY solutions.

Dead Key Fob Batteries

The remote key fob repairs key fobs for keys that come with cars make it easier than ever to open the trunk, doors, and tailgate. However, the battery inside the device could die. There are, however, a few tricks you can employ to solve this problem in an emergency.

Check to see if your vehicle is in ignition mode. If it is, the battery of the key fob may be drained instead of dead. To test this, press the fob's button against the ignition button on the vehicle. If it does not work, the battery is probably working fine and only has to be replaced.

To replace the battery in the fob, open the case using the screwdriver. Be cautious not to apply too much pressure as this could cause the fob to break in two. If the fob isn't opening, try using your pry tool more than once around the outside of the case.

Once the fob is opened, remove the mechanical key and then open the electronic part of the car. Insert the new battery and snap it back into the shell. If the key fob isn't working after this procedure, there could be a larger issue with your car's remote start system that requires a professional diagnostic. A reputable mechanic will capable of helping you if this is the situation. You can also call roadside assistance to assist with your vehicle, if you require it.

Broken Key Ring

If your key fob won't work because the ring is broken, there are a few things you might try. Check to see if you can find the broken piece inside the ignition. If it's still in there, remove it without damaging either the ignition lock or the door lock. If you are having trouble removing it, call an expert locksmith. They have tools that allow you to safely remove keys that are damaged from the ignition.

Another reason for a broken car key is corrosion on the circuit board or plastic frame. You can clean the circuit board by using a cotton swab and ruby alcohol. This will eliminate the corrosion and protect to the contact pads.

Repair a damaged rings by using a thick wire or nail to close the hole. Superglue can be used to repair the broken key ring. First, clean the broken ring with a damp towel and then apply a small amount superglue to the ends of the wire or nail. Apply the glue to the ring and let them dry before using your car. These DIY solutions may look appealing, but they're just temporary solutions. For long-term repairs, it's best to work with an experienced locksmith. They have the tools and knowledge to fix a broken car key quickly and effectively. They can replace the battery and reprogram your key fob, if needed.

Broken Key Blade

Some key blades may break due to wear and tear. If this happens, it's probably time to get a new key. Luckily, this problem isn't as severe as it appears at first. The most significant issue is that the metal blade broke off from the case.

One method to fix this is spraying the key hole with a lubricant. Then you can use pliers, tweezers, or a pin to grab the end of the broken key repair car and take it out. You could also make use of a magnet if the key is magnetic. Be cautious not to use a magnet on an ignition key because it could cause the tumbler of the lock to break.

If you're not able to take the broken piece of key, call an expert locksmith immediately. They have the right tools to safely extract keys without causing damage.

You can also use super glue to repair a snapped key. Apply a small amount glue to the edges of the break and press them together. After that, wait until the glue has dried before you insert your key into the lock. This method isn't secure and you may need to repeat the process a few times before it works. In addition the super glue might not be strong enough to hold the key together. This is more of a temporary solution rather than a permanent one.

Broken Plastic Loop

If your key fob's plastic loop is damaged it can render the key ineffective. Fortunately, this is an simple fix. For a replacement alternative, you can use a thick wire or finishing nail. Drill two holes in the plastic loop that is broken for each end of the nail or wire. Cut the nail or wire to the desired width and then place the superglue drop in each hole. Put the nail or wire into the holes to close them and let it dry.

A locksmith who sells replacement shells is a different option. They can take out the programmable portion of your key fob repair, transfer it to the new shell, and cut the new blade for less than the full replacement cost.

It's not the best solution, but it'll help you get back on the road if your key split in half. It can be difficult to Repair Car Key when the key blade is in the ignition, however. If you're not cautious you could make use of a hair clip or a needle to remove the broken part from the ignition. Contact a locksmith who has special tools to safely remove broken keys from ignitions. You can also have a new key made with the proper cuts to fit the ignition of your vehicle.

Broken Master Key

If a key gets damaged inside the lock, you'll need to find it before it gets completely destroyed. There are several methods you can employ, such as using lubricants and tools like needle nose pliers or tweezers to grab a fragment of the damaged key and then remove it.

To begin, spray the interior of your lock with a lubricant, such as graphite powder or WD-40. You can also try hacksaw blades, which involves sliding the blade along the side of a broken key and grasping onto a few of its 'teeth.' If you are successful you will be in a position to cut the damaged key repair service.

Another helpful tool is a spiral key extractor that is available in a wide range of hardware stores. It is a thin flexible rod with spiral threads that can be placed in the keyway, and later bent to the broken portion of the key. Once it has caught onto the serrations, you can turn the bar around and then pull it against the broken part of the key.

It's worth trying to get rid of a master key that's broken prior to calling a professional locksmith. If you're unable to pull a piece out, you need to call in the big guns to let a locksmith make you a brand new key and reprogram it to the transponder in your car.