The 10 Most Scariest Things About Car Key Button Repair

Car Key Button Repair

A damaged car key button can be a hassle. It is possible to contact a 24-hour locksmith Service for help or purchase a new remote key fob repair.

You could save money by fixing your old key fob instead of replacing it. This is especially true when the problem is caused by a worn switch or faulty contact.

Battery

If the buttons on your key fob aren't responding when you pressing them, this could be a sign the battery is dead or is nearing its end of life. Fortunately, replacing the battery is an easy task that you can complete on your own instead of hiring a locksmith or dealer to complete the task for you.

Locate the battery compartment first. This is usually found on the backside of the key fob. It may be hidden behind the cover, which slides out, or an access point that opens when you press the button. After the compartment is open you can look for the tiny button-cell battery. It's usually shaped as a coin and has an minus and plus sign. Remove the battery that is old, and replace it with a brand new one. Make sure the plus and minus symbols are aligned correctly.

Close the compartment and snap the two halves of your key fob. Make sure to align the two pieces and snap them in place properly before closing the door and testing your keys. Press any of the buttons to confirm that they work properly.

If your remote key fob stops working even after you replace the battery, it may be experiencing other issues that require a different form of repair. Physical damage from dropping the fob in a puddle for instance could cause it to cease functioning completely. It could also be a problem with the internal electrical system or need to be deprogrammed. Check out these other common auto troubleshooting techniques to determine if your key fob is suffering from a different issue.

Switches

Depending on the year and the manufacturer, there are various kinds of switches that are found in the keyfob of your car. The older style key has a chip that is visible inside the case. The newer keys work by sending signals to your car. Whatever the model of key, remote key fob repairs, More methods, the buttons on the key can get worn down or damaged when used regularly. This causes them to become difficult to press or even ineffective. If you try to force the button to work, it can cause further damage and may even stop the key from being able to start your vehicle in the future.

If you can't get your key to work Try changing the batteries. If it doesn't work, you may have to clean your key fob or re-adjust the switches. Because these tiny electronic switches spend a lot of time being moved around they are more prone to fail than the larger parts of your key.

The switches are rubber-like, and are coated with an electrically conducting film that can wear down over time. Fortunately, they are also small and affordable to replace. They're soldered on the circuit board, therefore you need to carefully take them off without causing any damage to other components. Then, you can solder the new ones in and rebuild your key fob.

Do not use your car key fob for more than a couple of hours at a time and don't leave it out in the open. Also, make sure you find a secure location to store your key when you're not using it.

If you've tried cleaning your key fob and replacing the battery, and the issue continues to persist it's probably time to consider a locksmith. A professional locksmith can check your key's frequency to see whether your car is capable of communicating. They can also open and replace microswitches as well as change cases, and more.

Outer Case

If the buttons can't move freely up and down in the case, they may become stuck or break. If cleaning the case using rubbing alcohol and a cotton swab fails to work, it might be necessary to take off the case. If the contacts that the buttons touch don't fit well or are worn out, adjusting them could be the only solution to fix the issue.

Rubber buttons be worn out over time. The rubber expands and nails pierce it, and the buttons become difficult to press. This can cause the key to fail, and in this case it is time for the replacement of the case or buttons. This repair involves disassembling the remote, finding the buttons on the circuit board, then heating the solder before carefully removing them. The circuit board is then soldered with new buttons. The case can be rebuilt and the horseshoe key blade piece can be inserted. The new buttons should be fitted snugly inside the case to prevent them from falling out.

Inner Case

Over time the buttons on your key fob may be damaged or stuck due to the continuous rubbing and accidental pressing. Using metal tape and a hole punch you can often quickly fix this problem when your car is not at home and the key fob doesn't work and you are unable to open the doors, but not to start the engine. This simple fix can allow you to safely return to your vehicle to finish your journey.